Click Image for Gallery
DPO6204B Hantek
Oscilloscope function | |||||
Acquisition | Real-time sample rate | 1 GSa/s(single channel) 500 MSa/s(two channels) | |||
250 MSa/s(three/four channels); | |||||
Note:digital channel 12,34 open at the same time,it is considered as one channel | |||||
Peak detection | Analog channel 4ns | ||||
Note:digital channels don’t support | |||||
Average mode | Analog channel | ||||
All channels reach N time samples at the same time,N can be selected from 2,4,8,16,32, 64,128,256,512 and 1024. | |||||
Note:digital channels don’t support | |||||
High resolution | Up to 12bit | ||||
Note:digital channels don’t support | |||||
Minimum test pulse width | 8ns | ||||
Memory depth | Single channel 64M | ||||
Two channels 32M | |||||
Three,four channels 16M | |||||
Input | Channel quantity | 4 analog channels | |||
Note:data channels can’t be opened | |||||
3 analog channels | |||||
Note:digital channel LA1/LA2/LA3/LA4/LA1LA2/LA3LA4 | |||||
2 analog channels | |||||
Note:digital channels infinitize | |||||
1 analog channel | |||||
Note:digital channels infinitize | |||||
0 analog channel | |||||
Note:digital channels infinitize | |||||
Input coupling | DC,AC or GND | ||||
Note:digital channels don’t support | |||||
Input impedance,DC coupling | Analog channel | ||||
25pF±3 pF,1MΩ±2% | |||||
Digital channel | |||||
(300KΩ±2%) ,(8 pF±3 pF) | |||||
Supported probe attenuation factor | Analog channel 1X,10X,100X,1000X | ||||
Voltage classes | 300V CAT II | ||||
Maximum input voltage | Analog channel 300VRMS (10X) | ||||
Digital channel -25V~25V | |||||
Horizontal | Waveform interpolation | (sin x)/x | |||
Maximum record length | Single channel maximum 64M | ||||
Two channels maximum32M | |||||
three/four channels maximum 16M | |||||
Horizontal scale range | DSO6084 DSO6104 | ||||
2ns/div~100s/div 1, 2, 5 step by step | |||||
Time base mode | Y-T,X-Y,Roll | ||||
X-Y number | Channel 1,2 1 XY channel,channel3 4 1 XY channel | ||||
Zero offset | ±0.5 div× minimum time base gear | ||||
Sample Rate and | ±25ppm | ||||
Delay Time Accuracy | |||||
Clock drifting | ≤±5 ppm/year | ||||
Delta Time Measurement | single,“acquisition”mode | ||||
Accuracy | |||||
(Full Bandwidth) | ±(1 sample interval+100ppm×reading+0.6ns) | ||||
>16 times averages | |||||
±(1 sample interval+100ppm×reading+0.4ns) | |||||
Sample interval=sec/div÷200 | |||||
Vertical | Bandwidth(-3db) | 6084 | 6104 | 6204 | |
80MHz | 100MHz | 200MHz | |||
Vertical resolution | Analog channel 8bit | ||||
Digital channel 1bit | |||||
Vertical scale range | nput BNC position is 500μV/div~10V/div | ||||
Position range | 500μV/div to 120mV/div,±1V | ||||
122mV/div to 1.2V/div,±10V | |||||
1.22V/div to 10V/div,±50V | |||||
Optional analog bandwidth limitation | Typical 20MHz | ||||
Bass response(-3db) | In BNC position is≤10Hz | ||||
Rising time in BNC position,typical | 6084 | 6104 | 6204 | ||
≤4.4ns | ≤3.5ns | ≤1.8ns | |||
Vertical gain accuracy | In “normal” or “average” acquisition mode,the accuracy o f 10V/div to 10mV/div is ±3% | ||||
In “normal” or “average” acquisition mode,the accuracy of 5mV/div to 500uV/div is ±4%. | |||||
DC offset accuracy | ±0.1 div±2 mV±1% offset value | ||||
The isolation of channels | DC maximum bandwidth:>40 dB | ||||
Note: Bandwidth reduced to 6MHz when using a 1X probe | |||||
Trigger | Trigger level range | ±5 divisions from the center of the screen | |||
Trigger mode | auto,general,single | ||||
Level | CH1~CH4 | ±4 divisions from the center of the screen | |||
Holdoff range | 8ns~10s | ||||
Trigger level accuracy | CH1~CH4 | 0.2 div×volts/div within ±4 divisions from the center of the screen | |||
Edge trigger | Slope | Rising edge,falling edge,rising or falling edge | |||
Signal source | CH1~CH4, | ||||
D1.0~D1.3, | |||||
D2.0~D2.3, | |||||
D3.0~D3.3, | |||||
D4.0~D4.3 | |||||
Pulse width trigger | Polarity | Positive polarity,negative polarity | |||
Condition(When) | <,>, !=, = | ||||
Signal source | CH1~CH4, | ||||
D1.0~D1.3, | |||||
D2.0~D2.3, | |||||
D3.0~D3.3, | |||||
D4.0~D4.3 | |||||
Pulse width range | 8ns ~ 10s | ||||
Video trigger | Signal standard | NTSC, PAL | |||
Signal source | CH1~CH4 | ||||
Synchronization | Scanning line,line number,odd field,even field,all field | ||||
Slope trigger | Slope | rise,fal | |||
condition(When) | <,>, !=, = | ||||
Signal source | CH1 ~ CH4 | ||||
Time range | 8ns ~ 10s | ||||
Overtime trigger | Signal source | CH1~CH4, | |||
D1.0~D1.3, | |||||
D2.0~D2.3, | |||||
D3.0~D3.3, | |||||
D4.0~D4.3 | |||||
DPO6204B Hantek |