PREORDER
Click Image for Gallery
DPO6204B Hantek
| Oscilloscope function | |||||
| Acquisition | Real-time sample rate | 1 GSa/s(single channel) 500 MSa/s(two channels) | |||
| 250 MSa/s(three/four channels); | |||||
| Note:digital channel 12,34 open at the same time,it is considered as one channel | |||||
| Peak detection | Analog channel 4ns | ||||
| Note:digital channels don’t support | |||||
| Average mode | Analog channel | ||||
All channels reach N time samples at the same time,N can be selected from 2,4,8,16,32, 64,128,256,512 and 1024. | |||||
| Note:digital channels don’t support | |||||
| High resolution | Up to 12bit | ||||
| Note:digital channels don’t support | |||||
| Minimum test pulse width | 8ns | ||||
| Memory depth | Single channel 64M | ||||
| Two channels 32M | |||||
| Three,four channels 16M | |||||
| Input | Channel quantity | 4 analog channels | |||
| Note:data channels can’t be opened | |||||
| 3 analog channels | |||||
| Note:digital channel LA1/LA2/LA3/LA4/LA1LA2/LA3LA4 | |||||
| 2 analog channels | |||||
| Note:digital channels infinitize | |||||
| 1 analog channel | |||||
| Note:digital channels infinitize | |||||
| 0 analog channel | |||||
| Note:digital channels infinitize | |||||
| Input coupling | DC,AC or GND | ||||
| Note:digital channels don’t support | |||||
| Input impedance,DC coupling | Analog channel | ||||
| 25pF±3 pF,1MΩ±2% | |||||
| Digital channel | |||||
| (300KΩ±2%) ,(8 pF±3 pF) | |||||
| Supported probe attenuation factor | Analog channel 1X,10X,100X,1000X | ||||
| Voltage classes | 300V CAT II | ||||
| Maximum input voltage | Analog channel 300VRMS (10X) | ||||
| Digital channel -25V~25V | |||||
| Horizontal | Waveform interpolation | (sin x)/x | |||
| Maximum record length | Single channel maximum 64M | ||||
| Two channels maximum32M | |||||
| three/four channels maximum 16M | |||||
| Horizontal scale range | DSO6084 DSO6104 | ||||
| 2ns/div~100s/div 1, 2, 5 step by step | |||||
| Time base mode | Y-T,X-Y,Roll | ||||
| X-Y number | Channel 1,2 1 XY channel,channel3 4 1 XY channel | ||||
| Zero offset | ±0.5 div× minimum time base gear | ||||
| Sample Rate and | ±25ppm | ||||
| Delay Time Accuracy | |||||
| Clock drifting | ≤±5 ppm/year | ||||
| Delta Time Measurement | single,“acquisition”mode | ||||
| Accuracy | |||||
| (Full Bandwidth) | ±(1 sample interval+100ppm×reading+0.6ns) | ||||
| >16 times averages | |||||
| ±(1 sample interval+100ppm×reading+0.4ns) | |||||
| Sample interval=sec/div÷200 | |||||
| Vertical | Bandwidth(-3db) | 6084 | 6104 | 6204 | |
| 80MHz | 100MHz | 200MHz | |||
| Vertical resolution | Analog channel 8bit | ||||
| Digital channel 1bit | |||||
| Vertical scale range | nput BNC position is 500μV/div~10V/div | ||||
| Position range | 500μV/div to 120mV/div,±1V | ||||
| 122mV/div to 1.2V/div,±10V | |||||
| 1.22V/div to 10V/div,±50V | |||||
| Optional analog bandwidth limitation | Typical 20MHz | ||||
| Bass response(-3db) | In BNC position is≤10Hz | ||||
| Rising time in BNC position,typical | 6084 | 6104 | 6204 | ||
| ≤4.4ns | ≤3.5ns | ≤1.8ns | |||
| Vertical gain accuracy | In “normal” or “average” acquisition mode,the accuracy o f 10V/div to 10mV/div is ±3% | ||||
In “normal” or “average” acquisition mode,the accuracy of 5mV/div to 500uV/div is ±4%. | |||||
| DC offset accuracy | ±0.1 div±2 mV±1% offset value | ||||
| The isolation of channels | DC maximum bandwidth:>40 dB | ||||
| Note: Bandwidth reduced to 6MHz when using a 1X probe | |||||
| Trigger | Trigger level range | ±5 divisions from the center of the screen | |||
| Trigger mode | auto,general,single | ||||
| Level | CH1~CH4 | ±4 divisions from the center of the screen | |||
| Holdoff range | 8ns~10s | ||||
| Trigger level accuracy | CH1~CH4 | 0.2 div×volts/div within ±4 divisions from the center of the screen | |||
| Edge trigger | Slope | Rising edge,falling edge,rising or falling edge | |||
| Signal source | CH1~CH4, | ||||
| D1.0~D1.3, | |||||
| D2.0~D2.3, | |||||
| D3.0~D3.3, | |||||
| D4.0~D4.3 | |||||
| Pulse width trigger | Polarity | Positive polarity,negative polarity | |||
| Condition(When) | <,>, !=, = | ||||
| Signal source | CH1~CH4, | ||||
| D1.0~D1.3, | |||||
| D2.0~D2.3, | |||||
| D3.0~D3.3, | |||||
| D4.0~D4.3 | |||||
| Pulse width range | 8ns ~ 10s | ||||
| Video trigger | Signal standard | NTSC, PAL | |||
| Signal source | CH1~CH4 | ||||
| Synchronization | Scanning line,line number,odd field,even field,all field | ||||
| Slope trigger | Slope | rise,fal | |||
| condition(When) | <,>, !=, = | ||||
| Signal source | CH1 ~ CH4 | ||||
| Time range | 8ns ~ 10s | ||||
| Overtime trigger | Signal source | CH1~CH4, | |||
| D1.0~D1.3, | |||||
| D2.0~D2.3, | |||||
| D3.0~D3.3, | |||||
| D4.0~D4.3 | |||||
DPO6204B Hantek
| |||||
